2nd Generation This includes all Eclipses, and Talons built from 1995-1999

Help engine problem! (VIDEO)

Thread Tools
 
Search this Thread
 
  #1  
Old 03-20-2008, 01:00 PM
keithscianna's Avatar
Thread Starter
Join Date: Oct 2006
Location:
Posts: 75
Default Help engine problem! (VIDEO)

My car started acting like it had a boost leak, No power while at full boost, Horrible idle, really rough and almost sounds like a tractor and it makes the whole car vibrate really bad. There is no exhaust leak at all also no boost leak. Also it is making a really wierd ticking/tapping noise. It is coming from inside the engine, it might be from the head but also could be bottom end its hard to tell where its coming from. and before this the engine was smooth as can be perfect idle and no lifter tick.I am wondering if maybe i skipped timing or somthing. Thanks,
http://www.youtube.com/watch?v=ZKJunU4rSsA
 
  #2  
Old 03-20-2008, 01:03 PM
Sebba's Avatar
Banned
Join Date: Feb 2006
Location: Austin, TX
Posts: 16,176
Default RE: Help engine problem! (VIDEO)

Spun bearing : (
 
  #3  
Old 03-20-2008, 01:16 PM
tjbiker031's Avatar
Senior Member
Join Date: Oct 2005
Location: Sarasota, FL
Posts: 689
Default RE: Help engine problem! (VIDEO)

start lookin for a 6-bolt.
 
  #4  
Old 03-20-2008, 01:29 PM
keithscianna's Avatar
Thread Starter
Join Date: Oct 2006
Location:
Posts: 75
Default RE: Help engine problem! (VIDEO)

i have a 6 bolt, lol is there any way to check for spun bearing without taking off oil pan?
 
  #5  
Old 03-20-2008, 01:46 PM
Sebba's Avatar
Banned
Join Date: Feb 2006
Location: Austin, TX
Posts: 16,176
Default RE: Help engine problem! (VIDEO)

No... but thats pretty conclusive.

It MIGHT.... just might be a loose pulley some place. Although I highly doubt it.
 
  #6  
Old 03-20-2008, 01:56 PM
RCJr9186's Avatar
Senior Member
Join Date: Jul 2005
Location: Summerville, SC
Posts: 5,650
Default RE: Help engine problem! (VIDEO)

taking the oil pan off is nothing but a few 10mm bolts. it takes longer to jack the car up than it does to take the pan off. you should be able to tell pretty quickly if you have a spun bearing or not by doing this.
 
  #7  
Old 03-20-2008, 02:01 PM
Sebba's Avatar
Banned
Join Date: Feb 2006
Location: Austin, TX
Posts: 16,176
Default RE: Help engine problem! (VIDEO)

Sometimes the bearing hasnt made its way to the oil pan yet. But you should see shavings in the pain.

By the way, the more you run it, the worse. One little metal chip gets circulated to the turbo and its toast.
 
  #8  
Old 03-20-2008, 03:03 PM
keithscianna's Avatar
Thread Starter
Join Date: Oct 2006
Location:
Posts: 75
Default RE: Help engine problem! (VIDEO)

Ok i will do that then, Do i just wiggle the rods and see if they move?
 
  #9  
Old 03-20-2008, 03:08 PM
Sebba's Avatar
Banned
Join Date: Feb 2006
Location: Austin, TX
Posts: 16,176
Default RE: Help engine problem! (VIDEO)

You should see a crap in the pan...
 
  #10  
Old 03-20-2008, 03:45 PM
RCJr9186's Avatar
Senior Member
Join Date: Jul 2005
Location: Summerville, SC
Posts: 5,650
Default RE: Help engine problem! (VIDEO)

ORIGINAL: Sebba
You should see a crap in the pan...
classic sebba post. almost sig material haha
 


Quick Reply: Help engine problem! (VIDEO)



All times are GMT -5. The time now is 04:22 PM.