So, my wonderful fiancee and i found a 1972 demon the day after my 28th birthday, and we decided to buy it...

Here are pictures of our Demon. It was moved to the shop the other day. The other parts of the grille and lights are in a box...and the hood isnt hinged properly yet, so it sits a little low.

Drivers side shot


Drivers side from the front


Passenger side corner


Rear shot


Paint up close


Rear quarter without the filler cap


Shot from the right rear




interior shots...this section (aside from the engine) needs the most work...but its all there, just take apart


Its got a BG wheel, but I wont be keeping that on


Race buckets


Inside the drivers door...you can see the parts that are exposed with the door liner on are painted black, and we have the liners


no cluster installed, but it came with three of them


rear deck, new carpeting


another dash and wheel shot


Clean engine bay








Undercarriage...its got alot of cobwebs and such hanging from it...its VERY clean, all redone.


under the front bumper


section of the unibody


underside of the trunk


rear dif, 8.75 rear with sway bar


under the front seats, with a ladder bar


looking back at the rear diff


another underbody shot



all is left now, is to build the motor, and put everything together...




some interesting info...
So, when we bought the demon, we were mostly just concerned with the car itself. It came with an engine which was laying on the floor, and a couple trannies, and TONS of other extra parts. We were told that the guy kept oil in the engine and he said that it would turn over with a wrench, but he was unsure of any specs on the motor. Although we have a 360 block pretty much ready to go, it would be a nice surprise if this engine, which looked completelty stock from the outside, would be good enough to clean up and use in the demon...


well, my dad got it apart a few days ago, and as soon as he got the first cylinder head off, he saw that this was no stock motor. unlike the stock flat top pistons, this engine had a very high dome piston, (which signifies lots of compression)...also a very expensive set of pistons; probably 600-700 dollars..where as cheaper pistons cost about 23 bucks a piece. unfortunately when he took the other cylinder head off, he found that there had been enough water in the engine to rust up the cylinder walls, and in the number 8 cylinder, the water froze and burst through the cylinder wall. there is so much rust in the other cylinders that the pistons are hard to get out, but as my dad has time during the day, he pisses around and wiggles them out...so far, he has gotten 4 of them out, and they appear to be in good enough shape. we have our fingers crossed for the other 4, and once the motor is stripped it will go to the machine shop to see if the motor is fixable.

for those who dont know, the mirada is a freak. unlike most cars running similar times with a small block, running high compression engines on 100+ octane race fuel, the mirada is only about 9 to 1 compression, so it runs on 87 octane. this makes racing very cheap because while many guys pay 6-10 bucks a gallon for race fuel, we only pay 2.09 (now). My intention with the demon is to have a motor that will run on regular pump gas, so no more than 10:1 compression...so if these pistons are good, they will be going into the mirada, and the mirada will have to be run on very high octane fuel...but it will have much greater potential for power. i called Federal Mogul, who made these pistons, and turns out they are 13.28 to 1 compression with a 62 cc cylinder head!

so it seemed that we might luck out and get a good set of pistons, and maybe a "good" block once i have it sleeved...but today, he found something else interesting. he had been trying to figure out what crank it was, as it was not a stock 340 crank. turns out, the engine was a stroker motor, and the crank and rods are in good shape. he found some numbers on the crank and checked them out, and we have found that this 340 is actually a 340 block, 30 over, displacing 361 cubic inches thanks to the stroker kit...

so, should everything be usable, the mirada will no longer be a low compression 340, but rather a high compression 361...

if the crank, rods, and pistons need more reconditioning work than we are willing to deal with, i will just buy decent new pistons and sell the stroker setup to someone who wants to put the effort into it, but the boss said that upon his initial inspection, the bottom end appears to be in very good shape.

 

Nice find! Everything looks clean and straight. Did you find any filler/ glass or did you get lucky enough to find a truly clean car where it was either cut and welded or original. I would imagine the rear end has some nice gearing/posi if they worked the motor and started prepping for race.

 

turbo it?

 

What are the heads? I mean if it's got a stroker kit in it then what valves and cams were they playing with in that thing? It'll be a beast once you finish it! So how bad did you rip the previous owner off?

 

... get a stock 350, get some low compression pistons, get a t88 with a thumper flange and go to town.

Nice car though, very clean!

 

Tha all important question that I was hesitant to ask!

 

Nice. Looks like its gonna be a fun project

 

I never heard of a Demon but, it reminds me of my old 74 Duster.

I will look for old pics if I can find them it was my 1st car when I was 17 a 74 or 75 Plymouth Duster Army tank green.

Anyway cool looking car.

 

I want the Demonemblem. That's all lol. That thing is cool as hell.

 

i know thats gonna be sick when it's finished.